IP Login Archives - 192.168.0.1 IP Admin Login

Linksys Router Login, Username, Password and IP

March 30, 2020 By Admin Leave a Comment

Looking out for a way to gain access to the Linksys Router setup page? Then you are in the right place. Here, we will guide you to get access to your Linksys router setup page. Before starting from today’s topics; if you are Linksys router you should be knowing about the model you have; If you don’t know, do check out the model you have first!

Linksys Router Login

Before starting from today’s topics just take a lot at the requirements you need to take care of for attaining access into the setup page.

First and foremost you need:

Linksys router,
Access to the internet via Ethernet or maybe WiFi also,
A web browser for getting access to the setup page.

If you are ready with the above-mentioned particulars then you are all set to start! So, let’s not wait and start with today’s steps by step tutorial on How to Login to a Linksys Router and Access the Setup Page.

1. Make Sure You Are Connected to Your Linksys Router

As mentioned above, you need to take a look at the requirement before you start. Skip this step if you are done with the requirement section. If not, then make sure first that you are connected with the internet either by Wi-Fi or by Ethernet port. Getting connected to the internet is the most basis first and foremost thing to do without the internet you can’t do any of the future steps!

2. Open Your Web Browser and Go to 192.168.1.1

After completing the first step; Now, let’s jump to the second step you need to do. As mentioned in the requirement section you need a fully working web browser for getting access.

Step 1: Get your web browser just go to the search bar and type this IP address 192.168.1.1.

Step 2: Just copy it from here and make sure that this number doesn’t change as this is an official IP address used to get to access into Linksys router site.

Step 3: If you are not getting your IP address then you can take a look at the IP address for your model as Linksys does have some of the models with different IP addresses.

Step 4: If you aren’t getting the IP address for your router then you use this for knowing the assigned IP address for the router model you are using. Or else you can also take a look at the manuals provided with the router for specific information about the router you are using.

If you are using the manual don’t keep the manual back as you will require to take a look at the manual again.

3. Enter the Username and Password for Your Linksys Router

Step 1: After getting connected with the internet and typing the particular IP address for the Linksys router. Then, you will be directed to a login page for the Linksys router you are using.

Note: Keep this in mind that the interface of the login page will depend on the model and version of the router.

Step 2: In the login section, you have to type the username and password for getting access.

Step 3: Don’t remember your username and password? Don’t worry, the Company itself set the usernames and password.

Step 4: If you don’t remember anything then you can get to know your official username and password from here. Or else, if you haven’t kept the manual back then you can check in manual for username and password.

Also Read:

How to Configure your Linksys Router

And now, you will be on the official configuration page. So now, you have access to bring any changes you need. If you aren’t aware of settings for that the better way is that you can write down the current setting or take a picture of your screen showing the current settings. This will be useful for you if you mess up somewhere in settings.

What If My Linksys Router or Network Stops Working After A Configuration Change

If by mistake the changes done by you tend to break the internet connection then you can follow a 30 30 30 reset trick for getting things ready to go! Or the easiest way, you can take a look at the default setting you have written and change. Also, you can take a look at the picture you have taken for reverting it.

Read More:

Belkin Router Login, Username, Password and IP

March 28, 2020 By Admin Leave a Comment

Belkin Router Login, Username, Password and IP: Nowadays, everyone is in the need of internet connection. Without the internet, one can’t imagine their life. In the era of browsing, gaming, streaming and more, the WiFi router is the single most important piece of technology in our home. Switch communicates a WiFi signal, permitting your gadgets to interface with one another and the web. Various switches are accessible from a wide range of produces. Setting up the Belkin router involves long-range and high connectivity with security.

Turn on the Belkin Modem/Router

Step 1 – The first step is to power up the Belkin modem. After that wait for all the lights to initialize which means that the modem is successfully connected to the ISP. Hence, the connection is established.

Step 2 – When all the connections are online, we have to connect the Ethernet of our wired internet, which will connect to our modem and router.

Step 3 – Now check whether both Belkin modem and Belkin router are able to connect to the internet by searching anything on them.

Step 4 – Connect the wireless devices to the Belkin modem or Belkin router. Wait for the connection.

Belkin Router Login and Manual Set Up

Here, we have mentioned some steps which help to manually set up the Belkin router.

Step 1 – First, we have to connect our device whether PC or laptop to any one of the Ethernet port of the Belkin router.

Step 2 – Further, searches any web page and enters the router default IP address in the given top bar and then press Enter. Belkin’s router default IP address will appear on your screen.

Step 3 – After that click on the login button to login to Belkin Router.

Step 4 – Just don’t add the password, otherwise, your connection will not step up properly.

Step 5 – Click submit.

Step 6 – To select the connection type, click the connection type under WAN.

Step 7 – Selects any connection type, whichever you want. After that, click next.

Step 8 – Enter your ISP details for further process and then click apply changes button.

Read More:

Setup Wireless Feature on Belkin Router

Step 1 – Open a web browser, search for Belkin’s router default IP to access the router.

Step 2 – Under the web page, go to Wireless ⇒ channel and SSID and configure the network name

Step 3 – When wireless settings have been configured, go to the wireless section, and then click Use as Access Point.

Step 4 – After that, select enable.

Step 5 – Enter a unique IP address.

Step 6 – Then, click on apply changes.

Step 7 – Connect your wireless device to your wireless connection.

Read More:

Enable Wireless Security:

Step 1 – The foremost step is to open your internet browser.

Step 2 – Then you have to enter the Belkin’s router IP address.

Step 3 – Press enter on your keyboard.

Step 4 – After that, you have to click on the security under wireless which displays on your screen. From the dropbox select WPA/WPA2- Personal. Click on apply changes appearing there

Step 5 – Click submit.

Step 6 – A box will appear on your screen, enter your password and then click on apply changes at the bottom.

Step 7 – After all these above-mentioned steps, you have saved your settings and the router will broadcast a secure wireless broadcast.

Spectrum Router Login, Username, Password and IP

March 28, 2020 By Admin Leave a Comment

In this article, we are going to talk about Spectrum Router Login, Username, Password and IP. Spectrum is well known for providing pre-configured wireless routers for its world customers. It provides network connections like cable connections, web connections, home phone connections, and, additionally, mobile connections. Spectrum additionally provides its services in an exceedingly explicit single affiliation or a combo connection.

How to Login to Spectrum Routers

Whereas during this era there’s such a lot of tech is concerned. In our network sector, the wireless network was one in every of absolutely the topper, and they are such a lot of web service suppliers; however, we are going to deal with the Spectrum routers and its login method.

1. Connect The Router To Your Home Network

The first and foremost Step to try during this configuration is before work. You wish to attach the router with a wireless network. Additionally to the present procedure, you furthermore may have to be compelled to connect it to your PC or smartphone.

If you’re unable to attach the router Wirelessly, then connect them through an Ethernet cable. Then you wish to connect one end of the Ethernet cable to your PC and another end to your router’s LAN port.

2. Insert The Router IP Address

Subsequently, you wish to open any browser in your PC. Type the IP address of your router in your universal resource locator bar. And search it for the results.

Note: The IP address of the router is available on the rear facet of the device.

After the router’s internet interface opens, it’ll raise the login id and password to urge details and different data concerning your device. As there are numerous router brands using spectrum networks, so for this, you need to enter your device model in credentials to avoid any sort of confusion.

There is a router of many brands like Sagemcom, Askey, Arris, Netgear, and SMC, etc., which all can use the spectrum interface. So please be assured of your router brand and its model. Mostly the default login id and password will be admin and password, respectively. If you are unable to know the credentials, then please try with those if it is the first time you are logging in.

Enter the required details such as login id and password according to your device brand. Further entering the particulars appropriately hit the login button, then you will be able to access the web interface of your router.

On the other hand, find the wireless setup for the spectrum router in the web interface of your router and insert internet credentials like IP address, subnet mask, and some other details to configure it.

3: Enter The Default Login ID and Password to Login to Spectrum Router

After receiving the default login id and password, enter them within the given space. Then, hit login to come into your router portal. If your credentials are correct, then you may be forwarded to the administrator’s page.

If your login id and password don’t match, then you wish to reset your router and take a look at till you get into the administrator page. Here is that the quick tutorial to reset your router and cause you to be accessible.

Also Read:

How To Reset Your Spectrum Router

Follow these Steps to reset your spectrum router. If you’re unable to match the login id and password within the router’s internet interface

Step 1: Firstly, you may notice the button on the router at the backside of the device. Hold it for a few seconds till the power light turns off.

Step 2: After that release, the button when the light glows up means the router is restarting. During the reboot process, all the LEDs will be blink continuously. Furthermore, the blinking will stop when the operation is over.

Step 3: Now repeat the login Steps, which mentioned above. You will be accessible to the administrator’s page without a doubt.

Xfinity/Comcast® Router Login, Username, Password and IP

March 28, 2020 By Admin Leave a Comment

Having trouble in login your brand new Xfinity router? Got new issues in your already existing router? Nobody is perfect and the same applies to the technology we use today. If you are looking for a username and password for your Xfinity Router, stay tuned. We bring you some tips and tricks to solve those challenges you face with the Comcast router.

Let us not forget to introduce ourselves to you. Importantly, we are the experts providing detailed and precise information on routers. Also, we are affiliates presenting the reviews on routers with a focus on public convenience. Moreover, any issues and queries relating to routers are our cues to solve.

Maybe you are someone using it for the first time or forgot about it. Undoubtedly, technology has made it simple to work online. Hush the fret since we got your back and solve Xfinity router login issues like second nature.

Xfinity/Comcast® Router Login

Step 1 – The first step to getting connected is going online. Your router, plug it directly into the system through a cable. Besides, you can even use it via WiFi wirelessly. To save the changes and risk of failure it is best to use a wired connection.

Step 2 – Next, cross-check the WiFi connectivity of your device. Confirm that your device’s connection to the internet is active. Because when your online you are in the power of changes.

Step 3 – After this, launch the web browser and type in 10.0.0.1 which is the login address. Additionally, 168.100.1or 192.168.1.1 are the alternatives to router login if 10.0.0.1 does not work. Remember to be careful and precise with the numbers and not mess them. This will cost you extra effort and time.

Step 4 – GIn case the address fails, verify your Comcast Router. The IP address which is displayed as ‘default gateway’ is the right one.

Step 5 – Subsequently, log in with username and password of the Xfinity router into the admin panel. Usernames and passwords have default values, the default credentials include:

The set credentials for admin are:

Root
User
Admin

The set credentials for the password are:

Motorola
High-speed
Password
W2402

Use these user names and passwords since they work with most routers. Further on, if it still doesn’t work we got you covered with pro tips. In the event your Xfinity Router Login is not successful, use our page’s search bar. Your router’s name, type in the search bar to know default username and password. Following this, the configuration page loads up. Go to network and router settings to change the preference and your router is set.

Also Read:

Frequently Encountered Problems in The Router Login

When the Router Login Fails: In this case, chances are that there is an error in entering the username and password. Ensure that you are inputting the exact username and password for your router. Also if you have recently changed the login details remember them firmly.

Forgot the Login Password: This used to be a hassle, but no more! A simple hard factory reset does the job. The back of your router has a black button, long-press it for 10 seconds. Count to 25 with a medium speed while long-pressing the black button and your job are Factory settings of the router will restore once you do this.

Router Login page Not Loading: A common issue encountered while loading pages on the internet. Firstly, your device’s internet connectivity has to be checked. Second, the Comcast router IP address has to be the right one, check for this. Command prompt has the details about this and any changes will be on display here

Netgear Router Login – www.RouterLogin.net

March 27, 2020 By Admin Leave a Comment

Netgear Router Login: It might have happened with you while trying to set up the Netgear router for your home network and to gain access that you were landed on a window that denies the access. Well, it is because you haven’t set the router properly. In that case, sit back and relax we got you all covered. Just read the information given below carefully without a doubt to get the best user experience.

How to Set Up Netgear Router

Before accessing the router login, it should be noted that you have configured the router set up correctly. Follow the given steps to configure your router:

Step 1: Connect an Ethernet cable and then connect your broadband to the internet port of your router and connect your computer to the LAN port of the router.

Step 2: Boost the router along with the modem and the computer.

Step 3: You are all set to access the Netgear routerlogin.net. Apart from this, you can use 192.168.1.1 IP address for login as well.

Step 4: Fill in the login details to access the setup page. By default, the login name is “admin” and the login password is “password”.

Step 5: After login, you will be directed to the smart setup wizard. Here, click on ‘yes’ then on the ‘next’ button.

Step 6: Save the settings you have made.

To authenticate the router connectivity click on the “router start” option.

Netgear Router Login – www.RouterLogin.net – Start Login page| Router login

Follow the subsequent steps to access the router login page:

Step 1 – Open the browser and enter the routerlogin.net address in the search box. Moreover, if you face any problem with this address you can always shift to 192.168.1.1.

Step 2 – Log in to gain access to all the settings for making your home network more secure.

What To Do When You Can’t Access to Routerlogin.net – Netgear Router Login Page?

Contrary to the efforts that you have made if you are still not able to gain access to the login page then, go through the following steps:

Step 1 – Clear the cache memory of the web browser and try again.

Step 2 – The firewall settings of your home network may be causing you the denial. So remove the firewall settings to gain access.

Step 3 – 192.168.1.1 is the default IP address and furthermore can also use 192.168.0.1 to gain access in case of trouble.

Step 4 – In case your WiFi is the reason for concern then, shift to an Ethernet cable to get access.

Step 5 – especially plug in the power source to your router properly.

Other Login Guides:

Things to Remember Before Accessing Router.net

1. Place the Netgear router and modem at distance, as it will make sure that the Wi-Fi signals do not conflict with each other.

2. If you are given external antennas with your router additionally. You must connect those antennas with the router and then access the Netgear router login. These antennas unquestionably help in improving connectivity.

3. If you don’t have enough space to place the router then you must make sure that you turn off all other WiFi devices for a better experience.

4. It should be noted that there is a continuous power supply for the router to work.

How to Improve the Working Capability

Moreover to improve the working capability of your router you should consider the subsequent things in particular.

Step 1: You must add external antennas with the router so that your router can send WiFi signals in a large area. You can buy these antennas from the official Netgear website also if you feel the need.

Step 2: Update the Firmware for the router as it will help you to improve the working potential of the router. You can easily find the updates on the official Netgear website.

Step 3: Change the default password to a new one and make sure it is a strong password so that no one access it without your permission.

Step 4: Adjust the channel bandwidth with the router to get better internet speed of your home network

Step 5: Routers should not be places where there are walls and other objects that may block the signals.

How to Change the MTU Size

In case you are facing slow internet speed issues even after configuration then, you also have the option to change the MTU size of the router. To do so, follow the steps:

Step 1: Open the router login page.

Step 2: Fill the login details.

Step 3: Click on ‘wireless settings’ after login.

Step 4: Change the Maximum transfer unit (MTU) from here.

Step 5: Then save the setting by clicking on ‘save’.

Step 6: Open the ‘cmd’ window and enter the command www.google.com-f-|1500.

Step 7: Open the ‘WAN setup’ option.

Step 8: Select the ‘MTU’ size you want for the router and click on the ‘apply’ option.

More Guides:

Having issues with Netgear router login?

If you are facing trouble with the router, you should reset the default setting of the router. To do that follow the following steps:

How to Reset the router using the smart setup wizard?

Step 1: Open the login page, enter your details and click ‘login’.

Step 2: After login find the ‘setup’ option.

Step 3: In the drop-down menu click the ‘reset‘ option.

How to Reset the Router Using the Reset Button?

Step 1: You can find a ‘reset‘ button at the backside of the router.

Step 2: Press the button for a few seconds.

Step 3: Now your router is reset to its default setting.

Conclusion

To conclude, getting access to the Netgear router login is not much difficult as it seems. You can consider the given steps above to solve each problem that you face while accessing the router login. You can easily manage the settings as per your requirement to get the best experience of internet surfing and in case you still come across any problem you can always drop your query at Netgear’s official website and the team will get back to you.

Happy Internet Surfing!